How to improve the sound quality of my Philips TV?
In order to improve the sound quality, make sure that you observe the following guidelines:
Check the quality of the incoming signal on the TV with a different Source like DVD or VCR
Splitting the signal will make it considerably weaker. If you use an antenna cable splitter: connect the antenna directly to the TV without the splitter.
Check your cables and cable-connections
Make all your cables as short as possible
Use high quality antenna cable
Connect the plugs well into their sockets
Check whether the sound quality has improved. If not:
You can use the smart settings in the TV Menu to set your TV to a predefined sound setting that will give you the best sound quality.
Press the [Home] button on the remote control to access the [Home] menu
Use the [Cursor buttons] to select [Setup] and press the [OK] button to confirm
Select [Smart Settings] and press the cursor [Right]
Press the cursor [Up][Down] to select a predefined smart setting and press the [OK] button to confirm
Press the [Back] button to exit the menu
Press the [Home] button on the remote control to access the [Home] menu
Use the cursor buttons to select [Setup] and press the [OK] button to confirm
Press the cursor [Down] to select [Sound] and press the cursor [Right] to access the sound menu
Press the cursor [Up][Down] to access the sound settings
Press the cursor [Right] to select and use the cursor buttons to adjust them to suit your preferences and press the [OK] button to confirm
Press the [Back] button to exit the menu
If there is no sound, press the [Mute] or volume button on the remote control
Check the connection with the audio system
Switch the audio system to the correct source
Turn the volume of the audio system up
If you do not have sound or bad sound on one or a few channels, the problem is with the reception or the broadcasting quality of these channels.
Fine-tune the channel(s). Fine-tuning can be useful when the frequency has shifted a bit or when interference of another frequency occurs.
Press the [Home] button on the remote control to access the [Home] menu
Use the cursor buttons to select [Setup] and press the [OK] button to confirm
Press the cursor [Down] to select [Installation] and press the cursor [Right] to access the installation menu
Press the cursor [Down] to select [Channel Install] and press the cursor [Right] to access the channel installation menu
If the channel lock is activated, the screen will prompt you to enter your pin code. If you have forgotten your pin code, refer to the FAQ ('I have forgotten my 4-digit pin code. How can I reset it?').
Press the cursor [Down] to select [Manual Install] and press the cursor [Right]
Press the cursor [Down] to SOUND SYSTEM and press the cursor [Right]
Check if the sound system is set to the correct sound system
If you are not sure of the sound system used in your location, press the cursor [Up]/down to select [AUTO] and press the [OK] button to confirm
Press the cursor [Down] to select [Fine Tune] and press the cursor [Right]
Adjust the frequency with the cursor [Up] or [Down] in case of poor reception of the channel found
Press the [OK] button once adjustment is completed
Press the cursor [Down] to select [STORE CUR CHAN] and press the cursor [Right]
Select OK and press the [OK] to store the frequency
Press the [Back] button to exit the menu
Reinstall the channels:
Press the [Home] button on the remote control to access the [Home] menu
Use the cursor button to select [Setup] and press the [OK] button to confirm
Press the cursor [Down] to select [Installation] and press the cursor [Right] to access the installation menu
Press the cursor [Down] to select [Channel Install] and press the cursor [Right] to access the channel installation menu
If the channel lock is activated, the screen will prompt you to enter your pin code. If you have forgotten your pin code, refer to the FAQ ('I have forgotten my 4-digit pin code. How can I reset it?').
Select [Channel Assistant] and press the cursor [Right] to access the automatic installation screen
Select [Start] and press the [OK] button to [Start] auto programming
The menu screen disappears and the progress of auto programming is displayed. The progress bar indicates the number of analogue channels found.
Once the installation is completed, press the [OK] button to confirm and exit the menu
If the problem is still not solved, contact the broadcaster or your provider to verify whether there is a broadcasting problem.
The information on this page applies to the following models:32PFL7694H/12 .
